Project

General

Profile

Files » acolab_prism_cura.ini

Michael Witrant, 12/03/2015 06:45 PM

 
1
[profile]
2
layer_height = 0.1
3
wall_thickness = 0.8
4
retraction_enable = True
5
solid_layer_thickness = 0.6
6
fill_density = 20
7
print_speed = 60
8
print_temperature = 205
9
print_temperature2 = 0
10
print_temperature3 = 0
11
print_temperature4 = 0
12
print_temperature5 = 0
13
print_bed_temperature = 0
14
support = None
15
platform_adhesion = None
16
support_dual_extrusion = Both
17
wipe_tower = False
18
wipe_tower_volume = 15
19
ooze_shield = False
20
filament_diameter = 2.85
21
filament_diameter2 = 0
22
filament_diameter3 = 0
23
filament_diameter4 = 0
24
filament_diameter5 = 0
25
filament_flow = 100.0
26
nozzle_size = 0.4
27
retraction_speed = 40.0
28
retraction_amount = 4.5
29
retraction_dual_amount = 16.5
30
retraction_min_travel = 1.5
31
retraction_combing = All
32
retraction_minimal_extrusion = 0.02
33
retraction_hop = 0.0
34
bottom_thickness = 0.3
35
layer0_width_factor = 100
36
object_sink = 0.0
37
overlap_dual = 0.15
38
travel_speed = 150.0
39
bottom_layer_speed = 20
40
infill_speed = 0.0
41
solidarea_speed = 0.0
42
inset0_speed = 0.0
43
insetx_speed = 0.0
44
cool_min_layer_time = 5
45
fan_enabled = True
46
skirt_line_count = 1
47
skirt_gap = 3.0
48
skirt_minimal_length = 150.0
49
fan_full_height = 0.5
50
fan_speed = 100
51
fan_speed_max = 100
52
cool_min_feedrate = 10
53
cool_head_lift = False
54
solid_top = True
55
solid_bottom = True
56
fill_overlap = 15
57
perimeter_before_infill = False
58
support_type = Lines
59
support_angle = 60
60
support_fill_rate = 15
61
support_xy_distance = 0.7
62
support_z_distance = 0.15
63
spiralize = False
64
simple_mode = False
65
brim_line_count = 20
66
raft_margin = 5.0
67
raft_line_spacing = 3.0
68
raft_base_thickness = 0.3
69
raft_base_linewidth = 1.0
70
raft_interface_thickness = 0.27
71
raft_interface_linewidth = 0.4
72
raft_airgap_all = 0.0
73
raft_airgap = 0.22
74
raft_surface_layers = 2
75
raft_surface_thickness = 0.27
76
raft_surface_linewidth = 0.4
77
fix_horrible_union_all_type_a = True
78
fix_horrible_union_all_type_b = False
79
fix_horrible_use_open_bits = False
80
fix_horrible_extensive_stitching = False
81
plugin_config = 
82
object_center_x = -1
83
object_center_y = -1
84

    
85
[alterations]
86
start.gcode = ;Sliced at: {day} {date} {time}
87
	;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
88
	;Print time: {print_time}
89
	;Filament used: {filament_amount}m {filament_weight}g
90
	;Filament cost: {filament_cost}
91
	;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
92
	;M109 S{print_temperature} ;Uncomment to add your own temperature line
93
	G21        ;metric values
94
	G90        ;absolute positioning
95
	M82        ;set extruder to absolute mode
96
	M107       ;start with the fan off
97
	;G28 X0 Y0  ;move X/Y to min endstops
98
	;G28 Z0     ;move Z to min endstops
99
	G1 Z15.0 F{travel_speed} ;move the platform down 15mm
100
	G92 E0                  ;zero the extruded length
101
	G1 F200 E3              ;extrude 3mm of feed stock
102
	G92 E0                  ;zero the extruded length again
103
	G1 F{travel_speed}
104
	;Put printing message on LCD screen
105
	M117 Printing...
106
end.gcode = ;End GCode
107
	M104 S0                     ;extruder heater off
108
	M140 S0                     ;heated bed heater off (if you have it)
109
	G91                                    ;relative positioning
110
	G1 E-1 F300                            ;retract the filament a bit before lifting the nozzle, to release some of the pressure
111
	G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
112
	G28 X0 Y0                              ;move X/Y to min endstops, so the head is out of the way
113
	M84                         ;steppers off
114
	G90                         ;absolute positioning
115
	;{profile_string}
116
start2.gcode = ;Sliced at: {day} {date} {time}
117
	;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
118
	;Print time: {print_time}
119
	;Filament used: {filament_amount}m {filament_weight}g
120
	;Filament cost: {filament_cost}
121
	;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
122
	;M104 S{print_temperature} ;Uncomment to add your own temperature line
123
	;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line
124
	;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line
125
	G21        ;metric values
126
	G90        ;absolute positioning
127
	M107       ;start with the fan off
128
	G28 X0 Y0  ;move X/Y to min endstops
129
	G28 Z0     ;move Z to min endstops
130
	G1 Z15.0 F{travel_speed} ;move the platform down 15mm
131
	T1                      ;Switch to the 2nd extruder
132
	G92 E0                  ;zero the extruded length
133
	G1 F200 E10             ;extrude 10mm of feed stock
134
	G92 E0                  ;zero the extruded length again
135
	G1 F200 E-{retraction_dual_amount}
136
	T0                      ;Switch to the first extruder
137
	G92 E0                  ;zero the extruded length
138
	G1 F200 E10             ;extrude 10mm of feed stock
139
	G92 E0                  ;zero the extruded length again
140
	G1 F{travel_speed}
141
	;Put printing message on LCD screen
142
	M117 Printing...
143
end2.gcode = ;End GCode
144
	M104 T0 S0                     ;extruder heater off
145
	M104 T1 S0                     ;extruder heater off
146
	M140 S0                     ;heated bed heater off (if you have it)
147
	G91                                    ;relative positioning
148
	G1 E-1 F300                            ;retract the filament a bit before lifting the nozzle, to release some of the pressure
149
	G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
150
	G28 X0 Y0                              ;move X/Y to min endstops, so the head is out of the way
151
	M84                         ;steppers off
152
	G90                         ;absolute positioning
153
	;{profile_string}
154
start3.gcode = ;Sliced at: {day} {date} {time}
155
	;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
156
	;Print time: {print_time}
157
	;Filament used: {filament_amount}m {filament_weight}g
158
	;Filament cost: {filament_cost}
159
	;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
160
	;M104 S{print_temperature} ;Uncomment to add your own temperature line
161
	;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line
162
	;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line
163
	G21        ;metric values
164
	G90        ;absolute positioning
165
	M107       ;start with the fan off
166
	G28 X0 Y0  ;move X/Y to min endstops
167
	G28 Z0     ;move Z to min endstops
168
	G1 Z15.0 F{travel_speed} ;move the platform down 15mm
169
	T2                      ;Switch to the 3rd extruder
170
	G92 E0                  ;zero the extruded length
171
	G1 F200 E10             ;extrude 10mm of feed stock
172
	G92 E0                  ;zero the extruded length again
173
	G1 F200 E-{retraction_dual_amount}
174
	T1                      ;Switch to the 2nd extruder
175
	G92 E0                  ;zero the extruded length
176
	G1 F200 E10             ;extrude 10mm of feed stock
177
	G92 E0                  ;zero the extruded length again
178
	G1 F200 E-{retraction_dual_amount}
179
	T0                      ;Switch to the first extruder
180
	G92 E0                  ;zero the extruded length
181
	G1 F200 E10             ;extrude 10mm of feed stock
182
	G92 E0                  ;zero the extruded length again
183
	G1 F{travel_speed}
184
	;Put printing message on LCD screen
185
	M117 Printing...
186
end3.gcode = ;End GCode
187
	M104 T0 S0                     ;extruder heater off
188
	M104 T1 S0                     ;extruder heater off
189
	M104 T2 S0                     ;extruder heater off
190
	M140 S0                     ;heated bed heater off (if you have it)
191
	G91                                    ;relative positioning
192
	G1 E-1 F300                            ;retract the filament a bit before lifting the nozzle, to release some of the pressure
193
	G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
194
	G28 X0 Y0                              ;move X/Y to min endstops, so the head is out of the way
195
	M84                         ;steppers off
196
	G90                         ;absolute positioning
197
	;{profile_string}
198
start4.gcode = ;Sliced at: {day} {date} {time}
199
	;Basic settings: Layer height: {layer_height} Walls: {wall_thickness} Fill: {fill_density}
200
	;Print time: {print_time}
201
	;Filament used: {filament_amount}m {filament_weight}g
202
	;Filament cost: {filament_cost}
203
	;M190 S{print_bed_temperature} ;Uncomment to add your own bed temperature line
204
	;M104 S{print_temperature} ;Uncomment to add your own temperature line
205
	;M109 T2 S{print_temperature2} ;Uncomment to add your own temperature line
206
	;M109 T1 S{print_temperature2} ;Uncomment to add your own temperature line
207
	;M109 T0 S{print_temperature} ;Uncomment to add your own temperature line
208
	G21        ;metric values
209
	G90        ;absolute positioning
210
	M107       ;start with the fan off
211
	G28 X0 Y0  ;move X/Y to min endstops
212
	G28 Z0     ;move Z to min endstops
213
	G1 Z15.0 F{travel_speed} ;move the platform down 15mm
214
	T3                      ;Switch to the 4th extruder
215
	G92 E0                  ;zero the extruded length
216
	G1 F200 E10             ;extrude 10mm of feed stock
217
	G92 E0                  ;zero the extruded length again
218
	G1 F200 E-{retraction_dual_amount}
219
	T2                      ;Switch to the 3rd extruder
220
	G92 E0                  ;zero the extruded length
221
	G1 F200 E10             ;extrude 10mm of feed stock
222
	G92 E0                  ;zero the extruded length again
223
	G1 F200 E-{retraction_dual_amount}
224
	T1                      ;Switch to the 2nd extruder
225
	G92 E0                  ;zero the extruded length
226
	G1 F200 E10             ;extrude 10mm of feed stock
227
	G92 E0                  ;zero the extruded length again
228
	G1 F200 E-{retraction_dual_amount}
229
	T0                      ;Switch to the first extruder
230
	G92 E0                  ;zero the extruded length
231
	G1 F200 E10             ;extrude 10mm of feed stock
232
	G92 E0                  ;zero the extruded length again
233
	G1 F{travel_speed}
234
	;Put printing message on LCD screen
235
	M117 Printing...
236
end4.gcode = ;End GCode
237
	M104 T0 S0                     ;extruder heater off
238
	M104 T1 S0                     ;extruder heater off
239
	M104 T2 S0                     ;extruder heater off
240
	M104 T3 S0                     ;extruder heater off
241
	M140 S0                     ;heated bed heater off (if you have it)
242
	G91                                    ;relative positioning
243
	G1 E-1 F300                            ;retract the filament a bit before lifting the nozzle, to release some of the pressure
244
	G1 Z+0.5 E-5 X-20 Y-20 F{travel_speed} ;move Z up a bit and retract filament even more
245
	G28 X0 Y0                              ;move X/Y to min endstops, so the head is out of the way
246
	M84                         ;steppers off
247
	G90                         ;absolute positioning
248
	;{profile_string}
249
support_start.gcode = 
250
support_end.gcode = 
251
cool_start.gcode = 
252
cool_end.gcode = 
253
replace.csv = 
254
preswitchextruder.gcode = ;Switch between the current extruder and the next extruder, when printing with multiple extruders.
255
	;This code is added before the T(n)
256
postswitchextruder.gcode = ;Switch between the current extruder and the next extruder, when printing with multiple extruders.
257
	;This code is added after the T(n)
258

    
(2-2/3)